Topic: 2011 XU motor ESC 4834 programing help (Read 2459 times)

eyeinsky · « **on:** June 23, 2013, 08:26:14 AM »

here's what I found http://www.alltraxinc.com/Products_ControllerPro.html

Here's the ESC in the Zero: Alltrax AXE4834

http://www.alltraxinc.com/Products_AXE.html

Please before I start any sugestion? How would I go about adding regen braking?

Thanks jerry http://www.elevationaerialoperation.com/

manlytom · « **Reply #1 on:** June 23, 2013, 10:36:12 AM »

hi there
not to put you off - if you program the alltrax and run into problems that might need a rest it can only be done by sending the controller back (physically !!!) to alltrax.

to config regen - someone else might know but I guess as in other 2010/2011 bikes the MBB controls everything and is not setup for regen.

best.

eyeinsky · « **Reply #2 on:** June 24, 2013, 03:18:33 AM »

Boes the MBB control speed?? why do i only get 40 mph 70 km top speed on my XU-lsm? I want the rate speed out of it... I thought if set the power curve up a little bit it would make a difference.

Jerry

NoiseBoy · « **Reply #3 on:** June 24, 2013, 03:52:19 AM »

This has been discussed previously. Its restricted by law.

eyeinsky · « **Reply #4 on:** June 24, 2013, 07:37:36 AM »

Quote from: NoiseBoy on June 24, 2013, 03:52:19 AM

This has been discussed previously. Its restricted by law.

The speed is restricted by law??? what law govern the speed of a bike to 40 mph?? the standar xu has no differences it will do 55 mph.

Jerry

eyeinsky · « **Reply #5 on:** June 24, 2013, 08:04:08 AM »

MBB

Motor Speed Control

Another box not sure what it is.

Battery box

Plug labled RAD not sure what is for.

OBD II connector, not sure what it is for yet

Clean up some of the wiring they sure do not secure the cables to well.

Picture of the bike stripped down of all panel and batteries

BSDThw · « **Reply #6 on:** June 24, 2013, 08:34:26 PM »

Quote

Another box not sure what it is.

It is the DC/DC for your 12V System.

Sorry I don't know the 2011 so I can't help more.

eyeinsky · « **Reply #7 on:** June 25, 2013, 04:30:00 AM »

Quote from: BSDThw on June 24, 2013, 08:34:26 PM

Quote
Another box not sure what it is.

It is the DC/DC for your 12V System.

Sorry I don't know the 2011 so I can't help more.

Thanks

So the BEC "Batt eliminator curuit"? that's what I thought.

Sweet If wanted to reduce load on the main Batteries I would start with this draw. I want to replace the BEC with 12v lipo pack. Later I want to regen tne pack with a regen brake system. Next step will be figure out how much the load of lights draw, with them converted to LED bulbs. Then seperat the 12v system from the main battery.

Jerry

eyeinsky · « **Reply #8 on:** June 25, 2013, 06:26:18 AM »

Quote from: NoiseBoy on June 24, 2013, 03:52:19 AM

This has been discussed previously. Its restricted by law.

I contacted Zero tonight they said they could un lock the LSM, I may just may have send them my MBB for reprogramming. Sign a release to do the modification.

Jerry