ElectricMotorcycleForum.com

  • September 01, 2026, 12:07:07 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

Electric Motorcycle Forum is live!

Pages: [1] 2

Author Topic: Centerstand for Experia  (Read 4833 times)

Bear-Tiger

  • Newbie
  • *
  • Posts: 22
    • View Profile
Centerstand for Experia
« on: April 19, 2026, 12:05:33 AM »
Hi there!
A first teaser: I´m building -with a little help from my friends- a centerstand for my Experia. Here is a first photo:


I modified a centerstand from a Yamaha MT09, smallered it to 170mm and added some brackets.
Today i had a first testride, clearence is ok, bike stands well, i have to do some paint and a little adjustment.
Logged

smithy

  • Sr. Member
  • ****
  • Posts: 453
    • View Profile
Re: Centerstand for Experia
« Reply #1 on: April 19, 2026, 02:47:51 AM »
Great result....well done Sir..!

Next time I see an MT-09, I'll check it out.

Smithy.
Logged
When I die, I wan't to go peacefully in my sleep like my Grandfather....not screaming like the passengers in his car.

Commodore

  • Jr. Member
  • **
  • Posts: 67
    • View Profile
Re: Centerstand for Experia
« Reply #2 on: April 19, 2026, 03:27:02 AM »
Congratulations!  Agreed, nice result to your experiment.

This gives me an opportunity to ask a question before I start my own experiments:  Was there ever any doubt about the case/casting not being able to withstand the forces transmitted by a center stand?  Or, as we've all been lead to think, a budget/supply issue?  Thanks!

Commodore
Logged

Bear-Tiger

  • Newbie
  • *
  • Posts: 22
    • View Profile
Re: Centerstand for Experia
« Reply #3 on: April 19, 2026, 10:31:47 AM »
Thanks.
Unfortunately, I don't know if there were any concerns about its strength. I haven't found any information on that.

The left mounting point is in the engine mount, where the side stand is also attached. So there shouldn't be any problems there. The right bracket is part of the engine and actually looks quite sturdy. I'm using 12mm bolts and dowel pins to mount the stand and minimize the load on the mounting points.

A large portion of the motorcycle's weight is supported by the stops for the stand position on center stands. Whenever I've seen center stands fail, these stops have always been the culprit, which is why I used 10mm thick steel blocks here.

Norbert
« Last Edit: April 19, 2026, 11:59:45 AM by Bear-Tiger »
Logged

jotjotde

  • Hero Member
  • *****
  • Posts: 617
    • View Profile
Re: Centerstand for Experia
« Reply #4 on: April 20, 2026, 11:18:37 AM »
Looks like a great job!

Do you plan to get it officially approved by the German TÜV?
I am convinced with a nice paintjob this modification will not rise questions, but you will need a killswitch like for the sidestand. The TÜV guy will definitely test this.

Just saying, because I currently have a problem with that, too. We need to find out how the thingie operates and connects to the bike's controls.

Was just a dumb assumption from my side. @smithy corrected me (see below)
« Last Edit: April 20, 2026, 05:33:05 PM by jotjotde »
Logged

smithy

  • Sr. Member
  • ****
  • Posts: 453
    • View Profile
Re: Centerstand for Experia
« Reply #5 on: April 20, 2026, 01:41:47 PM »
Quote from: jotjotde on April 20, 2026, 11:18:37 AM
Looks like a great job!

Do you plan to get it officially approved by the German TÜV?
I am convinced with a nice paintjob this modification will not rise questions, but you will need a killswitch like for the sidestand. The TÜV guy will definitely test this.

Just saying, because I currently have a problem with that, too. We need to find out how the thingie operates and connects to the bike's controls.

I don't know of any bike that has a kill switch on the centre stand....only on the side stand.

Smithy.
Logged
When I die, I wan't to go peacefully in my sleep like my Grandfather....not screaming like the passengers in his car.

Bear-Tiger

  • Newbie
  • *
  • Posts: 22
    • View Profile
Re: Centerstand for Experia
« Reply #6 on: April 20, 2026, 06:03:03 PM »
Quote from: jotjotde on April 20, 2026, 11:18:37 AM
Looks like a great job!

Do you plan to get it officially approved by the German TÜV?
I am convinced with a nice paintjob this modification will not rise questions, but you will need a killswitch like for the sidestand. The TÜV guy will definitely test this.

Just saying, because I currently have a problem with that, too. We need to find out how the thingie operates and connects to the bike's controls.

Was just a dumb assumption from my side. @smithy corrected me (see below)

No, i won't approve it by TÜV. Who will know, this bike is or is not sold with a centerstand? At least approving by TÜV is only a weared german thing, no other country cares. Worst case it takes two screws to unmount it. So what?

Norbert
« Last Edit: April 20, 2026, 06:04:41 PM by Bear-Tiger »
Logged

PWM

  • Sr. Member
  • ****
  • Posts: 401
    • View Profile
Re: Centerstand for Experia
« Reply #7 on: April 21, 2026, 09:50:54 AM »
Center stand looks great, can you give us a better picture on where it hard mounts to?

If motor casing then be careful use forward / reverse motion only and refrain from spinning bike once on the stand will snap them ears off...but you knew this already.
Logged
BMW eK75 Conversion (Retired)
Energica EVA Ribelle (Black Frame Matters)

Bear-Tiger

  • Newbie
  • *
  • Posts: 22
    • View Profile
Re: Centerstand for Experia
« Reply #8 on: April 21, 2026, 10:38:51 AM »
New photos will follow as soon as the center stand is finally mounted. Currently, the stand is being extended by another 20mm in height to ensure the rear wheel safely leaves the ground. The mounting sleeves are also not yet finished. Please bear with me.

Norbert
Logged

smithy

  • Sr. Member
  • ****
  • Posts: 453
    • View Profile
Re: Centerstand for Experia
« Reply #9 on: April 22, 2026, 01:44:41 AM »
Quote from: Bear-Tiger on April 21, 2026, 10:38:51 AM
New photos will follow as soon as the center stand is finally mounted. Currently, the stand is being extended by another 20mm in height to ensure the rear wheel safely leaves the ground. The mounting sleeves are also not yet finished. Please bear with me.

Norbert

Will be a great project when sorted...I look forward to seeing your work. You'll be one of the only "non promotional" Experias in the wild with a centre stand.

Smithy.
Logged
When I die, I wan't to go peacefully in my sleep like my Grandfather....not screaming like the passengers in his car.

CagivaRider

  • Full Member
  • ***
  • Posts: 101
    • View Profile
Re: Centerstand for Experia
« Reply #10 on: April 22, 2026, 02:22:24 AM »
Good work. I wondered when someone would just make one from another bike's centerstand. I have similar plans. Unfortunately, the motorcycle wreckers (junk yard) that was minutes from my home went out of business after forty years. I hoped to take measurements on the Experia and rummage through their centerstand piles for likely candidates. Now I may have to gamble on eBay or other online retailers.
Logged
2023 Energica Experia Launch Edition
2015 BMW F800GT
2001 Moto Guzzi V11-Sport
1987 Cagiva Alazzurra 650
1985 Yamaha RZ350

Bear-Tiger

  • Newbie
  • *
  • Posts: 22
    • View Profile
Re: Centerstand for Experia
« Reply #11 on: April 22, 2026, 10:43:01 AM »
Quote from: CagivaRider on April 22, 2026, 02:22:24 AM
Good work. I wondered when someone would just make one from another bike's centerstand. I have similar plans. Unfortunately, the motorcycle wreckers (junk yard) that was minutes from my home went out of business after forty years. I hoped to take measurements on the Experia and rummage through their centerstand piles for likely candidates. Now I may have to gamble on eBay or other online retailers.

Several years ago, I built a center stand for a Triumph Thunderbird Sport from the stand of a Triumph Tiger T400, so I had some idea of ??what I was getting myself into. Besides, I have a friend who's a metalworker and welder and helps me with projects like this.
If everything works to my satisfaction, I will publish further pictures, dimensions, and drawings of the required bushings. Then anyone who wants to put in the work can make their own center stand.
Norbert
Logged

Bear-Tiger

  • Newbie
  • *
  • Posts: 22
    • View Profile
Re: Centerstand for Experia
« Reply #12 on: April 29, 2026, 10:10:12 PM »
Hey everyone,

the center stand is finally finished.

The original center stand from a Yamaha MT09 was modified to be 170mm wide and 20mm taller. It now has metal blocks with 6mm threads and screws as stops when the bike is upright, as well as a thin metal strut that acts as a stop when the stand is folded. A machine shop made me stainless steel bushings that fit into the existing mounts on the motorcycle.

Tomorrow I'll take it for its first ride, hoping I don't throw any sparks at the asphalt...



By the way: I shortened the side stand by 15mm and fitted a significantly larger footplate. It's much more stable this way.

Logged

Bear-Tiger

  • Newbie
  • *
  • Posts: 22
    • View Profile
Re: Centerstand for Experia
« Reply #13 on: April 29, 2026, 10:16:04 PM »
Width
Logged

Bear-Tiger

  • Newbie
  • *
  • Posts: 22
    • View Profile
Re: Centerstand for Experia
« Reply #14 on: April 29, 2026, 10:19:56 PM »
Height
Logged
Pages: [1] 2