1
Zero Motorcycles Forum | 2013+ / Re: Charging to 100% SR/S 2020
« on: March 02, 2021, 03:20:04 AM »
I appreciate everyones help. Thank you
|
ElectricMotorcycleForum.com
- September 02, 2026, 04:46:46 AM
- Welcome, Guest
News:
Electric Motorcycle Forum is live!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Zero Motorcycles Forum | 2013+ / Re: Charging to 100% SR/S 2020
« on: March 01, 2021, 05:07:26 AM »
Just confirming that once it shuts off, its ok to unplug. I was at 80% and it went to 100% and shut off in less than an hour
3
Zero Motorcycles Forum | 2013+ / Charging to 100% SR/S 2020
« on: February 28, 2021, 11:18:10 PM »
Hi
I have another newbie question and would appreciate some thoughts. I have <1000 miles on the bike and usually keep the charge around 60%, since I'm not out much due to weather.
Yesterday I let it charge to 80 and so today since the weather is better I charged to 100. I was surprised that it took less then 1 hour to go from 80-100. I had been told that the last 5% could take 2-3 hours. It has shut down and I was curious why it didn't take longer. Also I had recently updated firmware to 19. I may just be a little neurotic, but I wanted to ask those with more experience
thanks in advance
I have another newbie question and would appreciate some thoughts. I have <1000 miles on the bike and usually keep the charge around 60%, since I'm not out much due to weather.
Yesterday I let it charge to 80 and so today since the weather is better I charged to 100. I was surprised that it took less then 1 hour to go from 80-100. I had been told that the last 5% could take 2-3 hours. It has shut down and I was curious why it didn't take longer. Also I had recently updated firmware to 19. I may just be a little neurotic, but I wanted to ask those with more experience
thanks in advance
4
Zero Motorcycles Forum | 2013+ / Re: Fault Code 27 12V low voltage
« on: February 28, 2021, 11:10:10 PM »
That you both for the help. I've had the bike out a few times and the error hasn't returned. Maybe it was related to how cold the garage was? 35ish ??
5
Zero Motorcycles Forum | 2013+ / Fault Code 27 12V low voltage
« on: February 17, 2021, 10:40:51 PM »
Hello
hoping to get some advice. I have a 202 SR/S and went to check the bike today. we have no electricity the last few days and it was 30ish F in the garage. When I started the bike, I received a Fault code 27.
Is there anything I need to do or watch out for?, I'm not sure how to charge the circuit if it won't start. My SOC has remained steady at 62%. Using firmware 19
Appreciate the help. I am a novice and still learning
Thank you
hoping to get some advice. I have a 202 SR/S and went to check the bike today. we have no electricity the last few days and it was 30ish F in the garage. When I started the bike, I received a Fault code 27.
Is there anything I need to do or watch out for?, I'm not sure how to charge the circuit if it won't start. My SOC has remained steady at 62%. Using firmware 19
Appreciate the help. I am a novice and still learning
Thank you
6
Zero Motorcycles Forum | 2013+ / Zero App- Ver 2.2.4(100)- Unable to record Ride Capture
« on: February 05, 2021, 11:57:22 PM »
Hi
I have had a difficult time capturing Ride capture on my iPhone. I have no problems with bluetooth. I am able to start the ride share capture, but as soon as I put up the kickstand or hip the motor stop switch I get a motorcycle armed message
telling me to unlock app functionality. I reverse the process, but I am unable to remove the message and see the information. I have had to close the app and start over, but when I do that, the ride capture shows 0 data.
I was hoping someone with more experience would be able to help. When I first purchased the bike a few months ago, I was able to look at the data. It may have been firmware 17. I had the same issue with 18 and now 19
thanks in advance
I have had a difficult time capturing Ride capture on my iPhone. I have no problems with bluetooth. I am able to start the ride share capture, but as soon as I put up the kickstand or hip the motor stop switch I get a motorcycle armed message
telling me to unlock app functionality. I reverse the process, but I am unable to remove the message and see the information. I have had to close the app and start over, but when I do that, the ride capture shows 0 data.
I was hoping someone with more experience would be able to help. When I first purchased the bike a few months ago, I was able to look at the data. It may have been firmware 17. I had the same issue with 18 and now 19
thanks in advance
Pages: [1]