1
Zero Motorcycles Forum | 2013+ / Re: Zero SR/F MY2020 OBD Cable to serial console
« on: January 16, 2020, 01:58:08 AM »
I just tried to get the eventlogs, but the MBB already gives the answer in the bottom:
|
ElectricMotorcycleForum.com
- September 03, 2026, 02:26:18 AM
- Welcome, Guest
News:
Electric Motorcycle Forum is live!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Zero Motorcycles Forum | 2013+ / Re: Zero SR/F MY2020 OBD Cable to serial console
« on: January 14, 2020, 01:26:04 AM »What do you mean about logs and a button?
Brian, what I meant is that the Zero diagnostics software the dealer is using has a GUI frontend with an embedded terminal emulator. This diagnostics software has a button for the dealer to login to a certain level (didn't check which one) through the terminal connection. It's hidden so you can't see the password it's using. Once logged in, you could change things. Things I can't without knowing the password..
I've never seen a device that produced anything but garbage at the wrong baud rate, Netpro must be working on something fancy. I think srf-fun is saying that he didn't see a password to get to a higher login level.
While I'm not sure about that, I can say that there are no decoded logs available at the default login level.
Auriga, I can confirm that I saw only garbage with a lower baudrate, nothing at all, not even the debug messages you see when turning the key..
Putting it on 115200 was the only way to get readable text, debug messages and menus..
About the logs I cannot confirm it yet as i didn't test that part, but it is in the menu, so i'm assuming it will be possible to just read them..
I'll test it out when i have time..
If you are talking about the logs in the attachment
3
Zero Motorcycles Forum | 2013+ / Re: Zero SR/F MY2020 OBD Cable to serial console
« on: January 10, 2020, 08:10:54 PM »
I succeeded to get in.. the pin's mentioned were correct, but the baudrate has to be 115200
then it works..
I saw the software running at the dealer, and wanted to play with the set accesory_configuration option to enable led indicators, but it failed..
I guess i have to login on the terminal but i don't have the password..
The zero diagnostics software logs in hidden with a button..
then it works..
I saw the software running at the dealer, and wanted to play with the set accesory_configuration option to enable led indicators, but it failed..
I guess i have to login on the terminal but i don't have the password..
The zero diagnostics software logs in hidden with a button..
4
Zero Motorcycles Forum | 2013+ / Zero SR/F MY2020 OBD Cable to serial console
« on: January 09, 2020, 09:17:18 PM »
Hi all,
I was wondering did somebody already tried to build the OBD2 to Serial cable to get your laptop connected to the MBB ?
I've followed the instructions here: https://zeromanual.com/wiki/How_to_build_a_cable_to_access_the_MBB
Used pin 5, 8 and 9, but nothing comes in on putty for the correct COM port and 38400 baud.. also tried changing TX and RX, same result..
I've seen the MBB software with my dealer, through the official cable, so I can confirm the software is still running and accessible through a serial connection.
But did they change the pins for the new cypher OS ?
anybody tried this ?
I was wondering did somebody already tried to build the OBD2 to Serial cable to get your laptop connected to the MBB ?
I've followed the instructions here: https://zeromanual.com/wiki/How_to_build_a_cable_to_access_the_MBB
Used pin 5, 8 and 9, but nothing comes in on putty for the correct COM port and 38400 baud.. also tried changing TX and RX, same result..
I've seen the MBB software with my dealer, through the official cable, so I can confirm the software is still running and accessible through a serial connection.
But did they change the pins for the new cypher OS ?
anybody tried this ?
Pages: [1]