ElectricMotorcycleForum.com

  • September 02, 2026, 12:08:09 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

Electric Motorcycle Forum is live!

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Creole

Pages: [1]
1
Zero Motorcycles Forum | 2013+ / Re: 2015 FX Will Not Turn On; No lights and no "click sound"
« on: November 11, 2017, 08:23:53 AM »
That is correct Ndm.  Once the battery is installed, the 12v side turns on.  Both batteries will turn on the 12v side in either of the battery slots with the loop back plug inserted (if only using one battery). When your dc/dc converter locked on, would the bike still turn on and do it’s precharge cycle?

2
Zero Motorcycles Forum | 2013+ / Re: 2015 FX Will Not Turn On; No lights and no "click sound"
« on: November 11, 2017, 04:22:19 AM »
I apologize for the confusion togo, but I don't think my update was very clear, so I just modified it.  But when I slide the power pack in, I'm not expecting any to happen until I turn the key on.  Instead, all the lights come on a second after the power pack is connected, and turning the key on/off does nothing.  Any ideas as to what might be causing that?

3
Zero Motorcycles Forum | 2013+ / Re: 2015 FX Will Not Turn On; No lights and no "click sound"
« on: November 10, 2017, 07:25:51 AM »
Update:  I got the high voltage replacement fuses in the mail earlier this week and went back to work on the bike this morning.  I replaced the fuse (#1), and the second I slide the power pack back in, a blank LCD lights up, headlight and tail light comes on, even though the key is not inserted :o The high beam/low beam switch works as do the blinkers (with the key still out).  Inserting the key and turning it on/off does nothing.  Pulling the power pack out will turn everything off, but reinserting it will yield the same results.  I haven't plugged the bike into charge because I'm not sure what might happen.

4
Zero Motorcycles Forum | 2013+ / Re: 2015 FX Will Not Turn On; No lights and no "click sound"
« on: October 30, 2017, 07:13:15 PM »
Thanks for the help Keith!  I was able to locate high voltage fuse #1, Main Bike Board/Controller, and it failed the continuity test.  Where as the #4, Charger Fuse, passed.  So I'm narrowing it down to the #1 fuse for now.  Do you have any idea as to why it might of blown?

Also, do you know where I might be able to find more information on best practices with the loop back plug?  I couldn't find anything in the manual or the unofficial zeromanual.com, and my search results on this forum are all over the place.

5
Zero Motorcycles Forum | 2013+ / Re: 2015 FX Will Not Turn On; No lights and no "click sound"
« on: October 29, 2017, 07:55:25 PM »
To add some context: 
- The bike had been stored indoors for about a week and unplugged for the duration. 
- The key was left in the ignition/key switch, but in the off position. (I live in a humid climate, could condensation have built up inside?)
- The last SOC prior to storing was 97%.

6
Zero Motorcycles Forum | 2013+ / 2015 FX Will Not Turn On; No lights and no "click sound"
« on: October 29, 2017, 07:46:22 PM »
Hello, I'm looking for some help from the wisdom of the forum.
I went to turn on my 2015 FX today, and when I turned the key (with the kill-switch in off position), I heard a faint pooping noise (like and old incandescent light bulb blowing).  No lights came on and I didn't hear the "click sound" of the contactor either.  I plugged the bike in to charge and I got the same results, no lights and no "click sound".  I subsequently got out the manual, removed the batteries and checked the '12 Volt Fuse Center', 'ABS 12 Volt Fuse', and the 'High Voltage Fuse' (#4) on the right side of the bike.  Although I'm not sure how to tell if the 'High Voltage Fuse' is blown, it looked normal and didn't smell burnt.  I have the protective cover removed on the left side, but I cannot find the two fuses (#s 1 & 2;pages 5.29-30), so I'm still looking.
Two questions:
1. Once I finally find the other two fuses, are they likely to be the problem?
2. If not, what could it be?  Any other trouble shooting recommendations?  Is there a way to test the Key Switch?

Pages: [1]