ElectricMotorcycleForum.com

Makes And Models => Zero Motorcycles Forum | 2013+ => Topic started by: SHAG on January 02, 2022, 11:02:43 AM

Title: Quick charger dimensions for the F series
Post by: SHAG on January 02, 2022, 11:02:43 AM

Can anyone supple the dimensions for the quick charger ? Zero part number 10-06919 for the F bikes?

Title: Re: Quick charger dimensions for the F series
Post by: MVetter on January 02, 2022, 02:31:52 PM

Sure

https://delta-q.com/product/quiq-1000-industrial-battery-charger/

Title: Re: Quick charger dimensions for the F series
Post by: SHAG on January 03, 2022, 08:14:53 AM

Thank you very much, MVetter

Title: Re: Quick charger dimensions for the F series
Post by: SHAG on January 18, 2022, 09:12:38 AM

Another question concerning the Quick Charger, which is shipping out to me tomorrow. When I remove the cover for access to the connector, will I find a removable male plug that stays there when the charger is not connected?

Title: Re: Quick charger dimensions for the F series
Post by: mdjak1 on January 19, 2022, 12:35:01 AM

See page 5.9 of the owners manual available on the Zero website.

https://www.zeromotorcycles.com/owner-resources

Title: Re: Quick charger dimensions for the F series
Post by: SHAG on January 19, 2022, 09:07:13 AM

Quote from: mdjak1 on January 19, 2022, 12:35:01 AM

See page 5.9 of the owners manual available on the Zero website.

https://www.zeromotorcycles.com/owner-resources

Thanks, and I have already looked at that page, but no information if the Power Pack Connector has a rain cover/plug.  I'm planning on cutting a flap in the Flexible Protective Cover like the diagram shows, but would like something to protect the connector from debris. Maybe it won't be an issue due to the location 

Title: Re: Quick charger dimensions for the F series
Post by: gt13013 on January 21, 2022, 06:02:00 PM

Do not cut anything. Just remove 2 of the screws that maintain the rubber. The rubber will stay in place without any problem, even with the missing screws.
https://www.youtube.com/watch?v=5VZz5fbscx0

Just to do not lose the screws, screw them back in place, but without the rubber. It is recommended to use some threadlocker, it will prevent the screws from unscrewing by themselves.
 

Title: Re: Quick charger dimensions for the F series
Post by: SHAG on January 23, 2022, 08:08:06 AM

Thank you. I appreciate that suggestion. It seems that on my bike, those 2 fasteners are plastic push ins.

I did receive the charger, and there is a diagram included that shows to cut a flap      ................  I have to turn the bike around to access that side.  I'll check it out
                                                                                                                           |________|
                                                                                                                     

Title: Re: Quick charger dimensions for the F series
Post by: gt13013 on January 23, 2022, 09:16:14 PM

Quote from: SHAG on January 23, 2022, 08:08:06 AM

It seems that on my bike, those 2 fasteners are plastic push ins.                                                                                                                   

I just checked on my FXS: there is one fastener only, and it is a screw. I have made another video:
https://youtu.be/S0f5c62LlI0
Note that the rubber stays perfectly in place without this screw.

Is it different on the FXE ?

Title: Re: Quick charger dimensions for the F series
Post by: SHAG on January 24, 2022, 09:16:23 AM

Yes! My FXE has 3 plastic push pins where your bike has screws. Two up top and one below.

I appreciate you helping me out with my new bike